In this menu, the user can decide how the phases will look in Veronte Panel, create checklists for each phase, create manual confirmation for particular phase changes and configure some notification that will appear behind the Veronte Unit (Side Panel) upon activation. 

Short Phases

The first menu gives the option to arrange the phases that will appear on the panel. Just dragging a phase and moving it wherever is desired will change its location in the panel. More than one phase can be arranged in the same line.

Phases Disposition


This feature is used to make sure that some requirements have been accomplished, for example, prior to a phase change or to avoid a possible malfunction.

In this menu, the checklist that will appear in the Panel is configured. The blue box displays all the phases configured for the operation. In each one of them, new elements for the checklist can be added with the button Add.

The configurable parameters for each element are:

  • Name: the name that will identify the element.
  • Type: the element chosen from the checklist can be one of the following types.
    • None: any action is performed, been just a check for the user to do something external to Pipe
    • Command: send to the UAV a position, a yaw angle or the wind velocity in the three axes.
    • In Range Check: Allows checking if a variable is between the range selected.
    • Atmosphere: set the atmosphere parameters  (temperature…).
    • Automation: selection between a set of automations, in order to only activate one of them for the phase that the aircraft is entering in.

Checklist Elements

Drag the automations into a group to create the selection, it is possible to have more than one. 

As an example, the following figure shows an automation selection on the checklist. The user has to select between two automations previously included in a group. Once one of them is selected, the other one will be automatically deactivated.automatio_check

Checklist Verification

  • Required for phase change: the element must be checked to go to another phase.
  • Show only once: the check will only appear the first time its phase is executed.

Checklist Configuration


This menu is used to create confirmation messages that appear when a button is pressed. It is a safety system for not pressing any keys by mistake.

By default, this window displays only one button to ask confirmation from: the radio link.

Panel Confirmation

For the other custom buttons created by the user for Veronte panel, the confirmation option is included when creating the button. When configuring the Button event, the system provides a check to include a confirmation when selecting that option (visit section 6.9).

When the user is trying to do an action (previously selected), Veronte Pipe will show a warning message like the following, asking us confirmation.


Confirmation  – Example


This menu is used to select which notifications will appear in the Side Panel and the way in which the user wants to hide them:

  • Mouse confirmation – It is necessary to pass with the mouse on notifications in order to hide them.
  • Auto-hide – Notification will auto hide in few seconds.
  • No show – The notifications will not show up.


Panel – Notifications

Besides the notifications that appear by default on this menu, it is possible to include some other system alarms or even custom ones created by the user. Click on “+” to display a popup window that allows the selection of a new variable. It is also possible to delete the notifications shown by default, click  on “-” to eliminate it from the error list.

In the following table, it will be described the error types of the notification panel.

NotificationCausePossible solution
GPS navigation downThe system is not connected to GPS signalCheck the GPS signal in the area and the GPS antenna connection
No writing telemetrySystem is not writing telemetry in the onboard logCheck the Air micro SD. It could be corrupted or without memory available
File system errorSystem has one or more corrupted filesTry to repeat the operation or check the micro SD files
Out of georeferenced areaThe GPS position is out of the areas with terrain altitude informationGo to Terrain Profile in Mission Panel and move manually Coarse and Fine areas or choose Auto to make the system doing it automatically and save.
Power A errorThe alimentation voltage is out of the admitted rangeGo to “Electrical” section of the manual to check admitted voltages
Servo X saturedThe servo number X is actually saturedCheck the servos panel to set the moving range
System not ready to start
  1. No GPS connection
  2. Licence expired
  1. See “GPS navigation down”
  2. Update the licence expiration
Task X real time errorSystem is not able to complete all tasks:

  • 1 means High level
  • 5 means Low level
Check system variables in Variables Panel and move the operations to a lower level.
Stick errorThe stick is not connected to Air autopilotCheck radio signal and stick connection (in case of HIL simulation it will be simulated)
Capture A errorThe Ground is not receiving the stick signalCheck the Ground-Stick connection
Inside Polygon XThe aircraft is actually inside the selected polygon (X is the polygon number)Exit the aircraft from the polygon


 Note: In some cases,  it will be necessary to restart the autopilot once the solution of one of this problems has been applied (“Out of georeferenced area” for example).